American Hunting & Fishing Supply storefront with pine trees and mountains behind

Supplying the World, One Person at a Time

Optics

Caring for Binoculars After a Dusty Trip

A careful post-trip routine protects lenses, coatings, hinges, and cases without turning ordinary field dust into permanent damage.

Feb 26, 20266 min readAmerican Hunting & Fishing Supply
Caring for Binoculars After a Dusty Trip

Dirt and grime from the trail, fingerprints from a hasty glassing, and dampness from a case can all shorten the life of your field optics. A few minutes of careful attention after each use can prevent scratches, clogged-up controls, cloudy surfaces and musty storage. Avoiding the most agressive cleaning methods and following the maker’s instructions for any special cleaning solutions, as opposed to general cleaning advice, is also critical to extending the life of your field optics.

Start with a dry inspection

Starting clean – a Dry Inspection We find that most people start cleaning their field optics by rubbing the lenses with a dry cloth. This can actually cause more problems than it solves. Start by placing your optics on a clean hard surface for inspection. Look for any visible signs of contamination on the objective lenses, eyepieces, focus wheel, hinge, strap mounts and body seams of the instrument. Look for any signs of moisture or contamination in the case, including the corners, the case’s lining, zip, and any padding found within the case.

Remove strap and other accessories before cleaning. You don’t want dirt on the accessories to be transferred to the optics when you put them back on. Check the case for dirt too. Open up the corners, check the lining, the zipper, and any padding found inside the case. If the case feels damp or has developed an ‘odour’ then leave it open in a dry, shaded, well-ventilated area while you clean the optics.

A flashlight at an angle can reveal very small particles. However, do not shine a very bright light into the glass of a lens as this can heat or even stress the equipment.

Remove loose dust before touching glass

Most optical cleaning devices are simple hand squeezed units which release a blast of clean air when squeezed, to clear surface dust from lenses and casings, including fine crevices and bolt holes. These types of units are best for cleaning up surface contamination. Once all large contamination has been cleared with an optical blowing device then a soft lens brush can be used to gently sweep away any remaining fine particles from lenses.

The hair from a lens brush can also be removed and cause problems. A brush with very soft bristles is best for this type of cleaning and it must have been previously used to clean optics. A shirt, paper towel, tissues, etc. can all transfer dirt to the optics and create stubborn marks that cannot be removed by normal cleaning.

Examination of focus and hinge areas need to be especially careful not to transfer any dirt into any of the joints or mechanisms, external surfaces can be wiped or brushed clean of loose particles. Later on when focusing becomes ‘stiff’ or ‘sticky’ do not attempt to use the optucally damaged instrument, refer to the makers’ servicing instructions.

Choose the least aggressive cleaning method

For tougher marks like fingerprints use a clean microfiber lens cleaning cloth to wipe the lens in a circular motion. Press with sufficient force to remove mark and then clean the cloth by folding it over to create a fresh surface. Continue until the mark is removed or until you use an approved cleaning solution on the cloth as instructed by the manufacturer.

Some products allow the use of a small amount of optical cleaning fluid that is applied to a clean lint-free wipe before use. However other products may specify the use of a particular solution or caution against the use of any cleaning fluid near certain seals, coatings or openings. Always refer to the manufacturer’s instructions for use when cleaning your optics and never apply any cleaning solution to the optics themselves.

Cotton swabs are best used for cleaning tight spaces, such as around the eyepiece, the housing seam or the small recesses found around the focus wheel and other operating parts. If, after having removed loose particles with air, there are still some remaining smudges of dirt, it is better to leave them be than to risk scratching the optics by continued wiping. Minor cosmetic blemishes can often be professionally cleaned or cosmetically touched up.

Clean the housing without spreading grit

Wipe exterior of Field Tray, Spotting Scope or Travel Case with a clean, slightly damp cloth only. Be sure to keep any moisture away from any of the following locations on your equipment: Eyepiece openings. Hinge gaps. Battery compartments. Other areas of the Field Tray, Spotting Scope or Travel Case that your specific maker’s written instructions list as being particularly sensitive.

Special care should be taken to clean around the bridge, when there are rubber eye cup covers, as well as for surfaces with special textures or covering. Dust, salt, sunscreen, skin oil and other trail grime can form sticky spots on these surfaces and pick up more dirt when the optics are next taken out of storage.

Empty out the stored contents of your case for your trip worn optics, take it outside and give it a good shake to loosen any remaining dirt. Then clean out the case itself for the interior surfaces using like materials for cleaning. Allow any wet stored items (linings or padding) to completely dry out before storing your optics away in their case for long periods of time. Store optics in their case for transport but store in a cool, dry location for long term storage – never in a closed case that may contain damp gear for extended periods.

Store optics ready for the next trip

If you have cleaned the surfaces of your field optics, then put the lens caps back on and put the field optics in a cool, dry location (e.g. away from direct sunlight, a heater etc.) for storage of long periods of time, then a case will also provide useful protection when you go on future trips. The case however needs to be stored for long periods of time in a dry room and not in a damp, poorly ventilated storage area.

Remember to store your optics away from: loose metal tools, dirty gloves, sharp objects etc. Do not store weight on your optics in their case and avoid storing them in a tightly wrapped plastic bag as this could contain moisture. Storage checks every few months will pick up on any problems such as dampness, residue or even a developing mechanical problem.

There are only a few things you need to watch out for, when it comes to maintaining your equipment: dry dust can be wiped off of lenses with dry grit between clean lens cleaning tissues, don’t use household glass cleaners, do not blow with your mouth on optics, and never spray any type of liquid on optics. Store your gear in dry locations and don’t put it away when it’s wet from a trip. This can take just a few moments of extra time after a long day, but can save a lot of time and money in the long run by extending the life of your gear.

Keep Reading

Related Field Notes

All Articles